Can Planes Fly in Snow?
Sources: FAA, EASA, ICAO · Updated May 2026
Yes — flights operate routinely in snow. Modern airliners are designed for winter operations, and a layered system of ground deicing, in-flight anti-ice, runway treatment, and operational procedures keeps snow flights safe. Before takeoff, ground crews spray heated Type I fluid to remove existing snow and ice, then optionally a thicker Type II, III, or IV anti-icing fluid that protects the airframe for a "holdover time" — typically 5 to 80 minutes depending on temperature and precipitation rate. In flight, engine bleed air or electric heaters protect wing leading edges, engine inlets, and probes. Runways are cleared and treated; pilots use contaminated-runway performance calculations. Heavy snowstorms still cause cancellations — not because aircraft cannot fly, but because the airport cannot keep up with the rate of accumulation.
Why snow on a wing is dangerous
Even a thin layer of snow, frost, or ice on a wing changes the airflow and can reduce lift by 30% or more while increasing drag and the stall speed. That is why every regulation (FAA, EASA, Transport Canada) imposes a "clean aircraft concept" — the wings, stabilizers, control surfaces, and engine inlets must be aerodynamically clean at the start of the takeoff roll. The job of ground deicing is to deliver that clean configuration into the takeoff roll despite ongoing snowfall.
The four deicing fluid types
A low-viscosity glycol-water mix sprayed at 60 °C (140 °F) or hotter. Job: melt and remove existing snow, ice, and frost from the airframe. Holdover time is short — minutes — because the fluid runs off the wing quickly.
Higher viscosity; clings to the wing and prevents new precipitation from sticking. Designed for aircraft with a rotation speed of 100 knots or more (sheds off during takeoff acceleration). Common on widebody and narrowbody commercial jets.
Designed for aircraft with a rotation speed below 100 knots — typically turboprops and regional jets. Behaves like a hybrid of Type I and Type II.
Same purpose as Type II but with the longest holdover times. The standard anti-icing fluid for commercial airliners in heavy snow or freezing rain. Designed to shear off during the takeoff roll.
Holdover time — the operational clock
Holdover time (HOT) is how long an anti-icing fluid keeps the wing clean under specified weather conditions. It depends on:
- →Fluid type, brand, and dilution ratio
- →Outside air temperature (colder weather generally shortens HOT)
- →Precipitation type and intensity (light snow vs heavy snow vs freezing rain)
- →Wind, sun exposure, ambient humidity
The FAA publishes Holdover Time Guidelines each summer for the upcoming winter — the FAA Winter 2025-2026 tables were published 12 August 2025. Beginning in winter 2021-22 the FAA added Degree-Specific Holdover Times (DSHOTs) for snow conditions, replacing broad temperature bands with finer-grain values. Type IV in moderate snow at -10 °C might give 25 minutes; in heavy snow at -25 °C, only 6 minutes. If the holdover expires before takeoff, the aircraft must return for a new application or be re-inspected.
In-flight anti-ice
Once airborne, separate systems prevent in-flight ice from forming:
- →Wing anti-ice: hot bleed air from the engines is ducted into the leading edge of the wings to keep the surface above 0 °C. On the Boeing 787, electric heater mats replace bleed air.
- →Engine anti-ice: bleed air heats engine inlets and nacelle lips.
- →Probe heat: electrically heated pitot tubes, static ports, angle-of-attack vanes, and total air temperature probes.
- →Windshield heat: electric heating to prevent fogging and ice.
Contaminated runways
Snow and ice on the runway change takeoff and landing performance. Airports continuously measure runway surface friction and report it through the Runway Condition Assessment Matrix (RCAM). Flight crews use runway condition codes (RWYCC 6 dry to RWYCC 0 ice) to recompute takeoff distance, landing distance, and crosswind limits. ICAO's Global Reporting Format for runway surface conditions (in force since November 2021) gives a standard worldwide language for these reports. When RCAM drops below the operator's minimums, the runway closes for clearing.
When snow does cancel flights
Cancellations happen for operational reasons, not because aircraft cannot fly:
- →Deicing capacity overwhelmed — deicing pads can only treat a few aircraft per hour
- →Runway closures for snow plowing
- →Ground equipment immobilized — pushback tugs, baggage carts, fuel trucks
- →Crew duty-time limits exceeded due to weather delays
- →Network ripple — inbound aircraft delayed at other airports
Sources
- FAA Holdover Time Guidelines Winter 2025-2026 (published 12 Aug 2025)
- FAA Notice 8900.557 — Revised FAA-Approved Deicing Program Updates
- EASA AMC and GM to Part-CAT — Ground Deicing and Anti-Icing
- ICAO Annex 14 Vol I — Aerodrome Design and Operations
- ICAO Doc 9981 — PANS-Aerodromes (Global Reporting Format)
- SAE AS6285 / AS6286 — Aircraft Ground Deicing/Anti-Icing Standards